The optimal time to use an ovulation test is between noon and 8 PM. For the best results, reduce your fluid intake approximately two hours prior to testing, and aim to test at the same time each day. Start testing around day 10 of your menstrual cycle, which is calculated from the first day of your period with red, flowing blood. Many individuals typically ovulate around day 14 of their cycle. We provide seven tests so you can test from day 10 to day 16 or from day 11 to day 17. You may notice a faint line as you approach ovulation; when this line becomes similar in color to the control line, it’s an ideal time to consider insemination.
How the Test Works
Ovulation is the process in which an egg is released from the ovary and enters the fallopian tube, where it can potentially be fertilized. For pregnancy to happen, the egg must be fertilized by sperm within 24 hours of its release. Just before ovulation, the body generates a significant amount of luteinizing hormone (LH), known as an “LH surge,” which typically occurs mid-cycle. The MakeAmom Ovulation Test helps predict ovulation and peak fertility by detecting this LH surge in urine, indicating that ovulation is likely to occur within the next 24 to 36 hours. It’s important to note that not all cycles will show an LH surge or result in ovulation.
Before You Begin
The MakeAmom Ovulation Kit includes multiple tests, allowing you to track your most fertile days. To determine when to start testing, first calculate the length of your average menstrual cycle—the number of days from the first day of your period to the day before your next period begins. Mark the number of days on the “When to Start Testing Chart.” If your cycle is irregular, consider using your shortest cycle length. You can refer to the SAMPLE CALENDAR and the accompanying example to ascertain your starting day for testing.
Instructions
- Remove the test from the pouch just before use and take off the cap.
- Avoid using first-morning urine for this test. For the most accurate results, test around the same time each day and limit your fluid intake about two hours before testing.
- Hold the test pointing downward directly into your urine stream for 10 to 15 seconds. Avoid urinating on the test or results window. Alternatively, you can urinate into a clean, dry container and dip the absorbent tip of the test into the urine for the same duration.
- Replace the cap and place the test on a flat surface. Start timing for 3 minutes.
Reading Your Results
While waiting for your results, you may see a colored solution moving across the test windows, which is normal. Wait 5 minutes to read the results, and do not interpret them after 10 minutes.
Positive Result = LH Surge
If two lines appear and the line in the round test window is similar to or darker than the line in the triangular control window, your LH has surged, indicating you are likely to ovulate in the next 24 to 36 hours.
Negative Result = No LH Surge
If two lines appear but the line in the round test window is lighter than the line in the triangular control window, your LH level has not surged. Additionally, if only one line appears in the control window, it means there was no LH surge. Continue testing daily.
Invalid Result
If no line appears in the triangular control window, the result is invalid. This may happen due to insufficient sample volume or incorrect test usage. Ensure you held the Absorbent Tip in the urine for at least 10 to 15 seconds. If you get an invalid result, repeat the test following the instructions with a new test.
Limitations of the Test
Review all provided information before conducting the test. Do not open the foil pouch until you are ready to perform the test. Not everyone ovulates mid-cycle; therefore, you may not see a positive result in the first five days of testing. Continue using the MakeAmom Ovulation Test to detect your LH surge. Certain prescription medications, such as menotropins for injection (Pergonal®) and danazol (Danocrine®), might affect your results. If you are taking Clomiphene Citrate (e.g., Clomid® or Serophene®), consult your physician regarding potential interference with the test. Some medical conditions or the onset of menopause can lead to elevated LH levels. Additionally, not everyone ovulates every cycle and may not see an increase in LH levels during non-ovulatory cycles.
For more insights into at-home insemination, you can visit MakeAmom’s website to understand how the process works. If you’re looking to connect with others on a similar journey, consider joining this free sperm donor matching group.
To summarize: The MakeAmom Ovulation Test is a helpful tool in predicting your ovulation window. By following the outlined instructions and reading your results accurately, you can identify your peak fertility days. For further guidance, check out this informative post about insemination syringes and their importance in achieving pregnancy. Also, you can explore this blog post to see how others have successfully used these methods in their fertility journeys. For an understanding of intrauterine insemination, visit Cleveland Clinic’s authoritative resource.